WSJT-X 2.7.0 - rc3

Those interested in digital modes may be pleased to hear that the latest release candidate of WSJT-X is available. I have no idea when this will be formally released.

See https://wsjt.sourceforge.io/wsjtx.html .

WSJT-X or JTDX?

Up to now, I have always used WSJT-X for FT8. There have been some reports that JTDX decodes more stations. 

Do you have view please? I try to use the latest released version.

WSJT-X 2.6.0 on general release?

I have been told that WSJT-X has been generally released as V2.6.0. I use WSJT-X for both FT8 and WSPR. Later today I expect to download this version if it is generally released. 

On the official website, it is still shown as a release candidate. Usually a new version is released about now, so perhaps my informant has advanced information?

WSJT-X latest version

Apparently there is a new version of WSJT-X available as a pre-release candidate. At the moment on WSPR and FT8 I use V2.5.4, which is the latest fully released version.  The latest candidate release is V2.6-rc4. I must download it and try it.

FT8 is now very popular. It is possible the decode sensitivity is slightly better with this newer version.

PI4 decoding

For some reason (probably by mistake) I assumed that PI4 was one of the modes supported by WSJT-X. Imagine my surprise today when I found it not there. My version of WSJT-X is 2.5.4.  

Instead I had to download some special software to decode PI4. I have not yet checked if there is a map upload a bit like PSKreporter maps.

I was hoping to decode one of the Irish beacons, EI1KNH/B on 40.013 MHz PI4.

If PI4 is not supported by WSJT-X why is it used rather than FT8 or WSPR by beacons? I don't think it is magically better than FT8.

My other questions are (1) what mode do I select and (2) what dial frequency do I set to decode EI1KNH/B in PI4? At the moment it is set to 40.013 DIG on the FT817ND, but I have no idea if this is correct.

UPDATE 2057z:  It looks like EI1KNH/B now uses FT8 instead of PI4, so I am now monitoring FT8 instead. It sends FT8 every 10 minutes. See https://www.qrz.com/db/EI1KNH/.  I shall monitor overnight.

10m FT8 RX

So far today, I have received loads of stations on 10m FT8 RX despite most of the antenna being on the ground awaiting the erection of the 8m dipole. 

I notice these were not being uploaded to PSKreporter for some reason, so I shall restart WSJT-X in case this is at fault.

UPDATE 1521z:  I did a resync to internet time and restarted WSJT-X: still no spots on PSKreporter.

UPDATE 1530z:  All now seems well, with 10 stations recently uploaded. This will remain a puzzle. All uploads relate to stations spotted in the last 20 minutes.

UPDATE 2022z:  208 stations spotted with much of the 10m antenna on the ground!! No spots reported for some reason until mid-afternoon. QRT soon.

UPDATE 2105z:  QRT. 

WSJT-X and 8m

OFCOM has told me my permit to TX on 8m is coming. My intention is to send FT8 most of the time, with the occasional CW and WSPR.

I know my widebanded FT817ND produces power at 8m and is clean. I also know PSKreporter supports 8m. Then, last night, I had a sudden panic. Did WSJT-X support 8m?  

This morning I checked - it does! I am sure with a hack it would have been possible, but in its standard form it does already. 

I hope to do some local CW crossband tests as well initially. My permit should start in early April and last for a year. 

WSJT-X on a Chromebook?

My shack PC runs Windows 10.  Currently it is almost exclusively used for WSJT-X.

My main PC in the lounge is an Asus Chromebook that I have used for about 2.5 years. It has been excellent: fast, the battery lasts for hours and it does nearly everything I want. It is also far less expensive than a Windows machine. My wife was also impressed and bought one. I would never go back to Windows. At first I was uncertain I had made the correct choice: I had.

At some point I may want to upgrade the Chromebook. If I do this, this current Chromebook might end up in the shack. Although the Chromebook will run Linux apps, I have never bothered.

Does anyone know how to install WSJT-X on a Chromebook please?

I am definitely NOT a computer nerd, so would need very simple instructions!

FT8 versus WSPR

Both these modes are part of the WSJT-X suite from Joe Taylor. 

WSPR needs about 6Hz of spectrum (not much) and 2 minutes for the most common form of WSPR.  WSPR is really a beaconing mode.  

FT8 is a communications mode and needs about 50Hz with 15 second TX slots. WSPR works with signals much weaker than FT8. FT8 works with signals much weaker than SSB or CW.

Both offer the minimum exchange of data and neither are "chatting" modes. As they work with very weak signals and need so little bandwidth they have been transformative in amateur radio. They are not instead of speech modes, but as well as.

There are other modes also available in the free WSJT-X suite.

Personally, I enjoy both modes, especially as my voice is poor since my 2013 stroke.

WSJT-X v2.3.0

Today the released version of WSJT-X V2.3.0 was made available. Previously just release candidates were available.

With Windows 10 I had all sorts of issues as it tried to block the download in case it harmed the PC. I said "keep" and "install anyway".  Only then could I go ahead.

WSJT-X rc4

The latest release candidate of WSJT-X has been released. It is rc4. When I tried to install it on my Windows 10 machine it kept blocking it. After going through the hoops several times I eventually installed it. This version runs until Feb 2nd when I expect to go through all this hassle again. I know why this is done: to keep the PC safe. rc3 no longer works after Jan 26th.

WSJT-X is used for FT8 and WSPR here

See https://physics.princeton.edu/pulsar/k1jt/wsjtx.html

New digital mode coming?

Southgate News reports that a new digital mode may be coming later this year called Q65 as part of WSJT-X suite.  I have just downloaded the latest release candidate for WSJT-X (2.3.0-rc3), but I have not checked if it is there. 

See https://physics.princeton.edu/pulsar/k1jt/Q65_Quick_Start.pdf

See http://www.southgatearc.org/news/2021/january/new-digital-protocol-q65.htm#.YAbrz_GTLrc

WSJT-X bug fixed?

Since changing to the latest release candidate version of WSJT-X it has been totally stable on FT8, whereas with V2.2.2 I often had issues with my USB SignaLink with no decodes and smeary waterfalls.  I use Windows 10 and I wonder if they did a bug fix?  The difference is very noticeable.

WSJT-X v2.3.0-rc2

For the last 12 hours or so, I have been using the latest "release candidate" version of WSJT-X, which is 2.3.0-rc2.  Certainly on FT8 it appears stable and works well. The only thing I have found is an annoying pop-up box saying I do not have logbook of the world on my PC. I seem to recall this on an earlier version.

See https://physics.princeton.edu/pulsar/k1jt/wsjtx.html

WSJT-X release candidate

There is a "release candidate" version of WSJT-X that introduces some new modes. Normally, these are issued as fully released versions soon when they have been beta tested and bugs removed.

See https://physics.princeton.edu/pulsar/k1jt/wsjtx-doc/wsjtx-main-2.3.0-rc1_en.html

WSJT-X bug?

Several times I have noticed a bug with WSJT-X with FT8. 

When I use my Windows 10 machine, it seems not to recognise my SignaLink USB interface until a few minutes after I have switched on. After a while it recognises it and starts to decode OK. Before then, signals on the waterfall look smeared and there are no decodes.  

At first I thought it was RF feedback, but it seems to be any band and any antenna. I have still to try the new release candidate version 2.3  to see if this has been corrected.

WSJT-X bug again

I am more convinced than ever that WSJT-X has a bug with Windows-10. This never happened with earlier versions of WSJT-X. I am using the latest released version. 

For some periods FT8 appears on the waterfall screen with smeary signals and no decodes. It is as if the decoder does not "get" the signals correctly. After a time it corrects itself and decoding starts. 

This is a real pain.

I might try the latest release candidate to see if this is better.

WSJT-X V2.2.2

Well over a month late, I have upgraded to V2.2.2.   I did try upgrading some weeks ago , but it said I was missing a dll, so I stuck with the older version. Today it installed fine. Not sure if this was Windows  is or WSJT-X. Anyway it is now installed and working fine.

New version of WSJT-X

At the moment there is a release candidate for a new version. I think the full release of this version is very close, so I'll wait for this.

See https://physics.princeton.edu/pulsar/k1jt/

WSJT-X issue

Just now I switched from 2m FT8 to 20m FT8. I was very puzzled that none of my spots were appearing on PSKreporter. I checked on the "all bands" tab and they were there!  For some reason PSKreporter was reporting me as still being on 2m!

After a restart, all was well with plenty of 20m RX and TX spots.

It seems that if you change bands you have to restart the programme or even restart the PC.

If you see rare DX stations reported on 2m, blame me!